Elite Home Finishes
CallWhatsApp

Services · East London & Eastern Cape

Electrician East London: Faults, DB Boards & COCs

A registered electrician for homes, businesses and industrial sites — installations, repairs, fault finding and COC certificates.

  • Free site visit
  • One written price
  • 7+ years on the tools
  • Warranty-backed work
Distribution board with three rows of breakers, wired and labelled by Elite Home Finishes
Distribution board with a main isolator, installed by our registered electrician
Neat distribution board with a clear cover fitted by our electrician

Registered electrician

Homes, offices, complexes and factories, wired and tested.

Comparing electricians in East London? Elite Home Finishes has a registered electrician on the team for residential, commercial and industrial electrical work across East London and every town within about 60km — from a tripping DB board or a dead plug circuit to a full rewire, a shop fit-out or maintenance on a factory floor. Every installation we complete is tested, and a Certificate of Compliance (COC) is issued only if you request one.

  • 60kmaround East London
  • Testedevery circuit we touch
  • COCon request

Most call-outs start with a symptom

Earth leakage trips when it rains

The unit is rarely the problem. The cause is usually water in an outside light fitting, a damaged cable or a faulty appliance. We switch circuits off one at a time and test, so the fault is found, not guessed.

We fault-find with proper test equipment before quoting, so you pay to fix the cause, not to swap parts until the tripping stops.

Lights flicker or dim

Usually a loose connection or a failing neutral somewhere upstream.

A plug circuit is dead

A tripped breaker, a broken link or a connection that has failed in the wall.

Burning smell at the DB board

Switch off and call us. It is often a connection that has been heating up for months.

Renovations & new work

We plan the layout with you

Where plugs, lights, switches, data points and outside lighting need to be, how many circuits the building needs and what size DB board will carry it. The same team does the ceilings, tiling and carpentry, so the electrical work is coordinated with the rest of the job.

Built for the coast

Salt and damp corrode outside fittings, isolators and connections, a big cause of the tripping we find in Beacon Bay, Gonubie and Nahoon. Outdoor work uses weatherproof, IP-rated fittings and sealed glands.

Commercial & Industrial Electrical

Electrical contractor for complexes, offices, new buildings and factories

From a block of flats to a factory floor, one registered electrician and one team: supply, boards, lighting and metering.

Managing a property? See our commercial and industrial page for the building trades we coordinate alongside the electrical work.

Offices & office blocks

Floor by floor, tenant by tenant

  • Distribution boards per floor and per tenancy
  • Tenant fit-outs: lighting, plugs, data points
  • Sub-meters, test reports and COCs for letting

Corporate & campuses

Head offices and business parks

  • Refurbishing old installations
  • Planned maintenance cover

Complexes & estates

Flats, townhouses, body corporates

  • Unit and common-area boards
  • Security and street lighting
  • Prepaid sub-metering

New buildings

Wired from the plans

  • Circuit and board planning
  • First-fix to final connection
  • COC on request

Factories & warehouses

Keeping production running

  • Three-phase and machinery circuits
  • Warehouse and yard lighting
  • Fast response to faults

Shops, clinics & guesthouses

Small premises, done properly

Shop fit-outs, clinic and surgery wiring and guesthouse refurbishments, with the compliance paperwork a lease or an insurer asks for.

What we handle on commercial sites

  • Three-phase supplySupply, isolators and circuits for plant and machinery.
  • Distribution boardsMain boards, floor boards and unit boards, labelled and tested.
  • Sub-meteringPrepaid and sub-meters so tenants pay for what they use.
  • Lighting & data pointsOffice, warehouse and yard lighting, plugs and data points.
  • Planned maintenanceScheduled checks and fast fault-finding when something stops.
  • COCs & test reportsThe paperwork that landlords, insurers and agents ask for.

For managing agents, developers & facilities managers

  1. 01

    Site walk & scope

    We walk the building with you or the managing agent and note what exists, what is failing and what the new work needs.

  2. 02

    Itemised quote & phasing

    A fixed quote with the must-fix items separated from the upgrades, planned around tenants, trading hours or the building programme.

  3. 03

    Install, test, hand over

    Every board and circuit is tested, labelled and signed off. A Certificate of Compliance is issued on request.

What's Included

What our electrical work covers

Core of the job

Fault finding — tripping earth leakage, dead circuits, flickering lights

  • DB board upgrades, replacements and new circuits
  • Full and partial house rewiring
  • New plugs, lights, switches and isolators
  • Electrical Certificates of Compliance (COC) for sales and insurance
  • Commercial electrical installations and shop fit-outs
  • Industrial electrical work — three-phase supply, machinery circuits, maintenance
  • Refurbishing old and non-compliant installations
  • Electrical planning for renovations and new builds
  • Inverter, backup power and solar wiring
  • Geyser wiring, isolators and timer switches
  • Outdoor, security and garden lighting
  • Electric fence installation and repairs
  • Prepaid meter and sub-meter installation

Our Work

Real photos from our own jobs

  • Distribution board with three rows of breakers, wired and labelled by Elite Home Finishes
  • Distribution board with a main isolator, installed by our registered electrician
  • Neat distribution board with a clear cover fitted by our electrician
  • Distribution board wired for an inverter, with a surge protection device fitted
  • New distribution board with a dark cover installed in a wall recess
  • New distribution board with surge protection and circuit breakers
  • Old distribution board with tangled, unlabelled wiring before Elite Home Finishes replaced the cover
    Before: tangled, unlabelled wiring
  • Same distribution board with a new labelled cover plate fitted by Elite Home Finishes
    After: new labelled cover plate
  • Gutted electrical box with loose wires hanging out before rewiring
    Before: loose wires, no board
  • Distribution board rewired with neat runs and insulated joints
    After: rewired and insulated
  • Old rusted distribution board with ageing breakers
    Before: old rusted board
  • New sub distribution board labelled flat fed from main DB with earth leakage
    After: new sub-board, earth leakage fitted
  • Old blue surface-mounted electrical box with exposed wiring
    Before: old surface box
  • Two-door distribution board with four rows of breakers and a meter
    After: new board with meter
  • Older distribution board retrofitted with digital energy meters
    After: energy meters added
  • Main supply cable terminations insulated inside a distribution board
    After: main cables insulated
  • New ceiling lights installed in a renovated room
    New ceiling lights
  • New wall switch and wiring in a finished room
    New switch and wiring
  • Gate motor with its controller and backup battery, repaired by Elite Home Finishes
    Gate motor repaired
  • Gate motor controller and backup battery fitted and working
    Gate motor: controller and battery

Swipe, drag or use the arrows for more

Our Approach

Why electrical work needs a registered electrician

  1. 01

    A registered electrician does the work and every installation is tested. A COC is issued only if you ask for one.

  2. 02

    We fault-find before quoting, so the fixed, itemised quote is for the actual cause of the problem.

  3. 03

    One team for the electrical work and the building work around it — no waiting for a separate contractor to come back and make good.

Your Options

Residential, commercial and industrial work

  • 01

    Residential electrical

    Repairs, fault finding, new plugs and lights, DB boards, rewiring and COCs for houses, flats and townhouses.

  • 02

    Commercial electrical

    Shops, offices, clinics and guesthouses — fit-outs, lighting, distribution boards and compliance for leases and insurers.

  • 03

    Industrial electrical

    Workshops, factories and warehouses — three-phase supply, machinery circuits, high-bay lighting and planned maintenance.

  • 04

    Planning & refurbishment

    Electrical layouts for renovations and new builds, and bringing old installations up to standard.

← Swipe or scroll for more →

How We Work

How we find, fix and certify electrical work

  1. 1

    Site visit & fault finding

    We inspect the installation, test the circuits involved and tell you plainly what we found.

  2. 2

    Fixed, itemised quote

    Materials and labour set out line by line — with the must-fix safety items separated from the optional upgrades.

  3. 3

    Installation or repair

    Work done to the wiring code, with the site left clean and any chasing or ceiling access made good.

  4. 4

    Testing & COC

    Every circuit we touch is tested. A Certificate of Compliance is issued only if you request one.

Planning Your Project

What decides the price of electrical work

We go through each of these at the free site visit, so the quote reflects your actual job.

  • 01

    Age of the installation — older houses often have no earth leakage protection, undersized wiring or a DB board that cannot take more circuits.

  • 02

    Earth leakage tripping — usually a fault on one circuit (often outside), which fault finding isolates instead of guessing.

  • 03

    Load — geysers, stoves, pool pumps, inverters and machinery all affect circuit sizing and the DB board you need.

  • 04

    Compliance — any addition or alteration to an installation needs to be tested and certified, and a COC is needed when a property is sold.

  • 05

    Coastal conditions — outside fittings, isolators and connections need weatherproof, corrosion-resistant components.

No surprises

What to expect before the power goes off

  • 7+ years on the tools

    Our team has been building and installing for over seven years: you're not paying for someone to learn on your home.

  • Free site visit

    We come to you, measure properly and talk it through, then send you a written quote. No call-out fee in East London suburbs, and no obligation.

  • Fixed, itemised price

    Every material and labour line is written down before work starts, so the price you approve is the price you pay.

  • Warranty-backed work

    Our workmanship carries a warranty, and manufacturer warranties on materials and products are passed on to you at hand-over.

Common Questions

Electrical questions, answered

  • Yes. Our electrical work is done by a registered electrician. If you need an electrical Certificate of Compliance (COC) for the installation, ask us and we issue it.

Clients Often Add

What clients add to electrical work

Service Area

Electrician Across East London & Surrounds

We work on electrician throughout East London and every suburb and town within roughly 60km, from the coast through to King William's Town, Bhisho and Berlin.

See all areas we serve →

Explore more

Free site visit · No obligation

Book your free electrical site visit

Tell us what is tripping, flickering or needs adding. We look at the board and quote in writing.